Differences between revisions 33 and 34
Revision 33 as of 2019-10-01 00:50:16
Size: 4258
Editor: AA6YQ
Revision 34 as of 2019-10-01 00:51:30
Size: 4296
Editor: AA6YQ
Deletions are marked like this. Additions are marked like this.
Line 41: Line 41:
   * In the '''CAT Serial Port''' panel, set the '''Port #''' for '''SatPC32''' tp '''-''' - the value in the selector just below '''COM64'''    * As shown in the above screen capture, in the '''CAT Serial Port''' panel, set the '''Port #''' for '''SatPC32''' to '''-''' (the value in the selector just below '''COM64''')

Interoperating with the SatPC32 Satellite Tracking Application

Note: the functionality described in this article requires Commander 14.2.6 (or later), DXKeeper 15.1.5 (or later), and SpotCollector 8.4.4 (or later)

Commander can be configured to interoperate with the SatPC32 satellite tracking application. In this form of interoperation, SatPC32 directly and exclusively controls your transceiver; Commander

  • interacts with with SatPC32 to track your transceiver's uplink frequency, downlink frequency, and mode, making these available to other applications just as it does when directly controlling a transceiver

  • obtains the current satellite name from SatPC32, and makes this available to other applications

    • to satisfy LoTW, AO-07 is reported to other applications as AO-7, and ISS is reported to other applications as ARISS

  • computes the satellite mode from the uplink frequency and downlink frequency, and makes this available to other applications


  1. on the Configuration window's General tab, set the Radio panel's Model selector to SATPC32

    • a SATPC32 panel will appear in the upper-right corner of Commander's Main window showing

      • connection status
      • if not connected to SatPC32, a Connect button

      • if connected to SatPC32 with its active satellite above the horizon, the name and mode of that satellite

    • panels and buttons not used when interoperating with SatPC32 will be hidden or disabled

  2. if SatPC32 is not already running
    1. start SatPC32
    2. after SatPC32 is running, click the Connect button in Commander's SATPC32 panel

  3. to facilitate rapid switching between the arrangement in which SatPC32 controls your transceiver and the arrangement in which Commander directly controls your transceiver, setup two radio definitions on the Configuration window's MultiRadio tab:

    • http://www.dxlabsuite.com/Wiki/Graphics/Commander/SatPC32.jpg

    Configured as shown in the above screen shot, Commander will enable you to switch between interoperation with SatPC32 and direct control of your transceiver with a single mouse click in the Main window's left-hand VFO panel.

    • As shown in the above screen capture, in the CAT Serial Port panel, set the Port # for SatPC32 to - (the value in the selector just below COM64)

    • Note the use of Selection by band to automatically select the IC-9700 when a 2m or 70cm frequency is selected.


If Commander is running and connected to SatPC32, typing a callsign into the Capture window's call box and striking the Enter key will populate these Capture window items:

  • Item

    Contents from SatPC32

    tx freq

    uplink frequency

    rx freq

    downlink frequency


    transceiver mode

    sat name

    satellite name

    sat mode

    satellite mode

If DXKeeper's Optimize for realtime QSO entry option is enabled, fields on the Main window's Log QSOs tab will be similarly populated when a callsign is typed into the QSO panel's call box and the Enter key is struck.


If Commander is running and connected to SatPC32 with SpotCollector's Spot xcvr split option enabled, the Notes box in the Outgoing spots panel at the top of SpotCollector's Main window will be populated with the active satellite' name followed by the word uplink and the current uplink frequency; additional information cannot be added to the Notes box.

Post a question or suggestion on the DXLab Discussion Group

Transceiver Control

Interoperation with Other Amateur Radio Applications

Getting Started with DXLab

SatelliteTracking (last edited 2019-12-11 17:20:04 by AA6YQ)