Differences between revisions 5 and 6
Revision 5 as of 2015-05-02 04:43:57
Size: 1618
Editor: AA6YQ
Comment:
Revision 6 as of 2015-05-02 04:48:23
Size: 2626
Editor: AA6YQ
Comment:
Deletions are marked like this. Additions are marked like this.
Line 10: Line 10:

 1. Configure your K3 or KX3 to decode CW, as described in the '''CW Text Decode Setup''' section of your owners manual

 1. In the '''Radio''' panel on the '''General''' tab of Commander's Configuration window, check the '''Convey decoded CW to WinWarbler''' box

 1. On the '''CW''' tab of !WinWarbler's Configuration window, check the '''display xmit/rcv characters''' box

 1. On !WinWarbler's Main window, set the '''Operating Mode''' panel to ''CW''

=== Transmitting and Receiving RTTY ===

To enable !WinWarbler to transmit RTTY via CAT command, on the '''External Modem''' tab of its Configuration window,

 1. set the '''Model''' selector to '''Xcvr Ctrl App'''

 1. check the '''RTTY''' panel's '''enabled''' box

 1. characters typed into WinWarbler's Main window's Transmit pane with the '''External Modem''' receive pane (denoted by an '''X''' in its left margin) active will be transmitted via your K3 or KX3

To enable !WinWarbler to display RTTY decoded by a K3 or KX3,

Configuring Command and WinWarbler for CW and RTTY Operation with an Elecraft K3 or KX3 using CAT Commands

An Electcraft K3 or KX3 can be directed to transmit CW, report decoded CW, transmit RTTY, and report decoded RTTY via CAT commands. Doing so requires both WinWarbler and Commander to be running, with Commander configured to control an Elecraft K3 or KX3.

Transmitting and Receiving CW

To enable WinWarbler to transmit CW via CAT command, set the Keying panel on the CW Tab of its Configuration window to Xcvr Ctrl App.

To enable WinWarbler to display CW decoded by a K3 or KX3,

  1. Configure your K3 or KX3 to decode CW, as described in the CW Text Decode Setup section of your owners manual

  2. In the Radio panel on the General tab of Commander's Configuration window, check the Convey decoded CW to WinWarbler box

  3. On the CW tab of WinWarbler's Configuration window, check the display xmit/rcv characters box

  4. On WinWarbler's Main window, set the Operating Mode panel to CW

Transmitting and Receiving RTTY

To enable WinWarbler to transmit RTTY via CAT command, on the External Modem tab of its Configuration window,

  1. set the Model selector to Xcvr Ctrl App

  2. check the RTTY panel's enabled box

  3. characters typed into WinWarbler's Main window's Transmit pane with the External Modem receive pane (denoted by an X in its left margin) active will be transmitted via your K3 or KX3

To enable WinWarbler to display RTTY decoded by a K3 or KX3,

  1. Configure your K3 or KX3 to decode CW, as described in the CW Text Decode Setup section of your owners manual

  2. In the Radio panel on the General tab of Commander's Configuration window, check the Convey decoded CW to WinWarbler box

  3. On the CW tab of WinWarbler's Configuration window, check the display xmit/rcv characters box

  4. On WinWarbler's Main window, set the Operating Mode panel to CW

Additional Topics


Post a question or suggestion on the DXLab reflector

Getting Started with DXLab

K3CWRTTYXcv (last edited 2018-10-24 02:51:07 by AA6YQ)