Differences between revisions 10 and 11
Revision 10 as of 2015-05-02 05:15:28
Size: 3206
Editor: AA6YQ
Comment:
Revision 11 as of 2015-05-02 18:40:14
Size: 3436
Editor: AA6YQ
Comment:
Deletions are marked like this. Additions are marked like this.
Line 13: Line 13:
 1. In the '''Radio''' panel on the '''General''' tab of Commander's Configuration window, check the '''Convey decoded CW to !WinWarbler''' box  1. In the '''Radio''' panel on the '''General''' tab of Commander's Configuration window,

   a. set the '''Command interval''' to ''100''

   a. check the '''Continuous interrogation''' box

   a.
check the '''Convey decoded CW to !WinWarbler''' box
Line 37: Line 43:
 1. In the '''Radio''' panel on the '''General''' tab of Commander's Configuration window, check the '''Convey decoded RTTY to !WinWarbler''' box  1. In the '''Radio''' panel on the '''General''' tab of Commander's Configuration window,      a. set the '''Command interval''' to ''100''

   a. check the '''Continuous interrogation''' box

   a.
check the '''Convey decoded RTTY to !WinWarbler''' box

Configuring Command and WinWarbler for CW and RTTY Operation with an Elecraft K3 or KX3 using CAT Commands

An Electcraft K3 or KX3 can be directed to transmit CW, report decoded CW, transmit RTTY, and report decoded RTTY via CAT commands. Doing so requires both WinWarbler and Commander to be running, with Commander configured to control an Elecraft K3 or KX3.

Transmitting and Receiving CW

To enable WinWarbler to transmit CW via CAT command, set the Keying panel on the CW Tab of its Configuration window to Xcvr Ctrl App.

To enable WinWarbler to display CW decoded by a K3 or KX3,

  1. Configure your K3 or KX3 to decode CW, as described in the CW Text Decode Setup section of your K3 or KX3 owners manual

  2. In the Radio panel on the General tab of Commander's Configuration window,

    1. set the Command interval to 100

    2. check the Continuous interrogation box

    3. check the Convey decoded CW to WinWarbler box

  3. On the CW tab of WinWarbler's Configuration window, check the display xmit/rcv characters box

  4. On WinWarbler's Main window, set the Operating Mode panel to CW

Decoded CW will appear in the CW receive pane on WinWarbler's Main window. Decoded information can be captured by double-clicking.

Transmitting and Receiving RTTY

To enable WinWarbler to transmit RTTY via CAT command, on the External Modem tab of its Configuration window,

  1. set the Model selector to Xcvr Ctrl App

  2. check the RTTY panel's enabled box

  3. On WinWarbler's Main window, set the Operating Mode panel to RTTY

Characters typed into WinWarbler's Main window's Transmit pane with the External Modem receive pane (denoted by an X in its left margin) active will be transmitted via your K3 or KX3.

To enable WinWarbler to display RTTY decoded by a K3 or KX3,

  1. Configure your K3 or KX3 to decode RTTY, as described in the Data Text Decode Setup section of your K3 or KX3 owners manual

  2. In the Radio panel on the General tab of Commander's Configuration window,

    1. set the Command interval to 100

    2. check the Continuous interrogation box

    3. check the Convey decoded RTTY to WinWarbler box

  3. on the External Modem tab of its Configuration window,

    1. set the Model selector to Xcvr Ctrl App

    2. check the RTTY panel's enabled box

  4. On WinWarbler's Main window, set the Operating Mode panel to RTTY

Decoded RTTY will appear in the the External Modem receive pane (denoted by an X in its left margin) on WinWarbler's Main window. Decoded information can be captured by double-clicking.

Additional Topics


Post a question or suggestion on the DXLab reflector

Getting Started with DXLab

K3CWRTTYXcv (last edited 2018-10-24 02:51:07 by AA6YQ)