Differences between revisions 1 and 19 (spanning 18 versions)
Revision 1 as of 2015-05-02 04:24:32
Size: 508
Editor: AA6YQ
Comment:
Revision 19 as of 2016-04-04 21:16:48
Size: 4004
Editor: AA6YQ
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
== Configuring Command and WinWarbler for CW and RTTY Operation with an Elecraft K3 or KX3 using CAT Commands == == Configuring Commander and WinWarbler for CW and RTTY Operation with an Elecraft K3 or KX3 using CAT Commands ==
Line 3: Line 3:
An Elecraft K3 or KX3 can be directed to transmit CW, report decoded CW, transmit RTTY, and report decoded RTTY via CAT commands, eliminating the need for any external interface. Doing so requires both !WinWarbler and Commander to be running, with Commander [[TranceiverControlElecraft|configured to control an Elecraft K3 or KX3]]. Note that a connected P3 configured to display decoded CW or RTTY interferes with the K3's ability to report decoded CW or RTTT to Commander, and thus [[DisableElecraftP3DecodedTextDisplay|must be disabled]].
Line 4: Line 5:
==== Additional Topics ==== 1. Tap the Menu button
2. Rotate the Select knob to SVGA Menu
3. Tap the Select knob
4. Rotate the Select knob to SVGA Data
5. Tap the Select knob to toggle Data Display on or off
Line 6: Line 11:
=== Transmitting and Receiving CW ===

To enable !WinWarbler to transmit CW via CAT command,

 1. set the '''Keying''' panel on the '''CW''' Tab of its Configuration window to ''Xcvr Ctrl App''

 2. the K3 or KX3 should be in ''FSK D'' data submode

To enable !WinWarbler to display CW decoded by a K3 or KX3,

 1. configure your K3 or KX3 to decode CW, as described in the '''CW Text Decode Setup''' section of your K3 or KX3 owners manual

 1. in the '''Radio''' panel on the '''General''' tab of Commander's Configuration window,

   a. if the '''Command interval''' is set to more than ''200'', set it to ''200''

   a. check the '''Interrogation''' box

   a. check the '''Convey decoded CW to !WinWarbler''' box

 1. On the '''CW''' tab of !WinWarbler's Configuration window, check the '''display xmit/rcv characters''' box

 1. On !WinWarbler's Main window, set the '''Operating Mode''' panel to ''CW''

Decoded CW will appear in the CW receive pane on !WinWarbler's Main window. Decoded information can be [[CapturingDecodedInformation|captured by double-clicking]].

=== Transmitting and Receiving RTTY ===

To enable !WinWarbler to transmit RTTY via CAT command, on the '''External Modem''' tab of its Configuration window,

 1. set the '''Model''' selector to '''Xcvr Ctrl App'''

 1. check the '''RTTY''' panel's '''enabled''' box

 1. On !WinWarbler's Main window, set the '''Operating Mode''' panel to ''RTTY''

Characters typed into !WinWarbler's Main window's Transmit pane with the '''External Modem''' receive pane (denoted by an '''X''' in its left margin) active will be transmitted via your K3 or KX3.

To enable !WinWarbler to display RTTY decoded by a K3 or KX3,

 1. Configure your K3 or KX3 to decode RTTY, as described in the '''Data Text Decode Setup''' section of your K3 or KX3 owners manual

 1. In the '''Radio''' panel on the '''General''' tab of Commander's Configuration window,

   a. if the '''Command interval''' is set to more than ''200'', set it to ''200''

   a. check the '''Continuous interrogation''' box

   a. check the '''Convey decoded RTTY to !WinWarbler''' box

 1. on the '''External Modem''' tab of its Configuration window,

   a. set the '''Model''' selector to '''Xcvr Ctrl App'''

   a. check the '''RTTY''' panel's '''enabled''' box

 1. On !WinWarbler's Main window, set the '''Operating Mode''' panel to ''RTTY''

Decoded RTTY will appear in the the '''External Modem''' receive pane (denoted by an '''X''' in its left margin) on !WinWarbler's Main window. Decoded information can be [[CapturingDecodedInformation|captured by double-clicking]].

=== Additional Topics ===
 * [[K3PSKRTTY|Connecting and configuring the Elecraft K3 for PSK, RTTY, CW, and Phone operation]]

Configuring Commander and WinWarbler for CW and RTTY Operation with an Elecraft K3 or KX3 using CAT Commands

An Elecraft K3 or KX3 can be directed to transmit CW, report decoded CW, transmit RTTY, and report decoded RTTY via CAT commands, eliminating the need for any external interface. Doing so requires both WinWarbler and Commander to be running, with Commander configured to control an Elecraft K3 or KX3. Note that a connected P3 configured to display decoded CW or RTTY interferes with the K3's ability to report decoded CW or RTTT to Commander, and thus must be disabled.

1. Tap the Menu button 2. Rotate the Select knob to SVGA Menu 3. Tap the Select knob 4. Rotate the Select knob to SVGA Data 5. Tap the Select knob to toggle Data Display on or off

Transmitting and Receiving CW

To enable WinWarbler to transmit CW via CAT command,

  1. set the Keying panel on the CW Tab of its Configuration window to Xcvr Ctrl App

  2. the K3 or KX3 should be in FSK D data submode

To enable WinWarbler to display CW decoded by a K3 or KX3,

  1. configure your K3 or KX3 to decode CW, as described in the CW Text Decode Setup section of your K3 or KX3 owners manual

  2. in the Radio panel on the General tab of Commander's Configuration window,

    1. if the Command interval is set to more than 200, set it to 200

    2. check the Interrogation box

    3. check the Convey decoded CW to WinWarbler box

  3. On the CW tab of WinWarbler's Configuration window, check the display xmit/rcv characters box

  4. On WinWarbler's Main window, set the Operating Mode panel to CW

Decoded CW will appear in the CW receive pane on WinWarbler's Main window. Decoded information can be captured by double-clicking.

Transmitting and Receiving RTTY

To enable WinWarbler to transmit RTTY via CAT command, on the External Modem tab of its Configuration window,

  1. set the Model selector to Xcvr Ctrl App

  2. check the RTTY panel's enabled box

  3. On WinWarbler's Main window, set the Operating Mode panel to RTTY

Characters typed into WinWarbler's Main window's Transmit pane with the External Modem receive pane (denoted by an X in its left margin) active will be transmitted via your K3 or KX3.

To enable WinWarbler to display RTTY decoded by a K3 or KX3,

  1. Configure your K3 or KX3 to decode RTTY, as described in the Data Text Decode Setup section of your K3 or KX3 owners manual

  2. In the Radio panel on the General tab of Commander's Configuration window,

    1. if the Command interval is set to more than 200, set it to 200

    2. check the Continuous interrogation box

    3. check the Convey decoded RTTY to WinWarbler box

  3. on the External Modem tab of its Configuration window,

    1. set the Model selector to Xcvr Ctrl App

    2. check the RTTY panel's enabled box

  4. On WinWarbler's Main window, set the Operating Mode panel to RTTY

Decoded RTTY will appear in the the External Modem receive pane (denoted by an X in its left margin) on WinWarbler's Main window. Decoded information can be captured by double-clicking.

Additional Topics


Post a question or suggestion on the DXLab reflector

Getting Started with DXLab

K3CWRTTYXcv (last edited 2018-10-24 02:51:07 by AA6YQ)