Differences between revisions 6 and 7
Revision 6 as of 2006-10-30 15:57:20
Size: 2945
Editor: c-24-60-113-193
Comment:
Revision 7 as of 2006-11-22 20:46:43
Size: 3023
Editor: c-24-60-113-193
Comment:
Deletions are marked like this. Additions are marked like this.
Line 2: Line 2:
PC control of an Icom transceiver is accomplished via a bidirectional CI-V bus, which uses an asynchronous protocol communicated via TTL voltage levels. Thus an interface between your PC and transceiver is required. PC control of an Icom transceiver is accomplished via a bidirectional CI-V bus, which uses an asynchronous protocol communicated via TTL voltage levels. Thus an interface between your PC and transceiver is required; the Icom CT-17 provides this function.
Line 16: Line 16:
Here are some off-the-shelf products: ==== Alternative interfaces ====
Line 18: Line 18:
http://k1nu.home.comcast.net/k1nu/Products/ [http://k1nu.home.comcast.net/k1nu/Products/ K1NU interfaces]
Line 20: Line 20:
http://www.cssincorp.com/prod-cable.htm [http://www.cssincorp.com/prod-cable.htm Creative Services Software interfaces]
Line 22: Line 22:
http://home.att.net/~n8st/icom.html [http://home.att.net/~n8st/rigcontrol.html Donner Digital Interfaces]
Line 26: Line 26:
[http://g4zlp.co.uk/unified/StandardIcomCAT.htm ZLP Electronics CT-17 replacements]

Line 28: Line 31:
You can also purchase a CT-17 from Icom, but they cost twice to three- times more than the above products, and offer no advantage. See http://www.grove-ent.com/CT17.html .

==== Home-brew interfaces ====

Connecting an Icom Transceiver to your PC

PC control of an Icom transceiver is accomplished via a bidirectional CI-V bus, which uses an asynchronous protocol communicated via TTL voltage levels. Thus an interface between your PC and transceiver is required; the Icom CT-17 provides this function.

The basic function of the interface is voltage level conversion from the RS-232 levels used in a standard serial port (+12 and -12 VDC) and the TTL levels used by your transceiver (+5, and 0 VDC). The interface itself requires power, which can be provided either externally, or with some circuits by using one of the serial port modem control signals as a power source.

There are two decisions that will drive your choice:

1. do you want to use one of your PC's serial ports, or one of its USB ports?

2. would you prefer to build something or buy it?

Being able to choose #1 is a relatively new phenomenon. Previously, controlling a transceiver via USB port meant purchasing a USB-to- serial-port adaptor (e.g. from Belkin or ByteRunner) and connecting it to your interface's serial port. Now, however, there are off-the- shelf USB interfaces; see, for example http://www.microham.com/USB% 20interfaces.html . You can also build one of these yourself, as described in http://www.eham.net/articles/8192 ; if you go this route, be sure to read the comments, as the circuit as presented contains an (easily correctable) defect.

If your PC has a spare serial port, or you'd prefer an outboard USB- to-serial-port converter, then you'll have many more choices with respect to the interface - down both the "buy it" and "build it" paths.

Alternative interfaces

[http://k1nu.home.comcast.net/k1nu/Products/ K1NU interfaces]

[http://www.cssincorp.com/prod-cable.htm Creative Services Software interfaces]

[http://home.att.net/~n8st/rigcontrol.html Donner Digital Interfaces]

http://home.comcast.net/~n4vas/wsb/html/view.cgi-home.html-.html

[http://g4zlp.co.uk/unified/StandardIcomCAT.htm ZLP Electronics CT-17 replacements]

You'll find product reviews of the above, along with more alternatives at http://www.eham.net/reviews/products/53 .

Home-brew interfaces

Building a interface is a nice little project that can be accomplished in an afternoon, including the trip to Radio Shack and back. This circuit was published many years ago in QST; its very reliable, and you may already have the necessary parts laying around:

http://www.qsl.net/civ_commander/interface.jpg

Another nice circuit,

http://www.seed-solutions.com/gregordy/Amateur%20Radio/Experimentation/CIVInterface.htm

uses the MAX-232 IC for level conversion rather than discrete transistors. It also includes a circuit to control your 706's PTT circuit using one of the serial port modem control signals, which you'll find convenient if you're planning to operate digital modes.


[:TransceiverControl:Transceiver Control]

[:GettingStarted:Getting Started with DXLab]

ConnectingIcom (last edited 2020-04-30 16:46:51 by AA6YQ)