Differences between revisions 7 and 8
Revision 7 as of 2012-03-25 07:03:50
Size: 1580
Editor: AA6YQ
Comment:
Revision 8 as of 2012-03-25 07:22:29
Size: 3409
Editor: AA6YQ
Comment:
Deletions are marked like this. Additions are marked like this.
Line 7: Line 7:
 1. Using a [:ConnectedVirtualSerialPortPairs: Connected Virtual Serial Port Pair], connect CW Skimmer's '''CAT interface''' to PowerSDR-IF's '''CAT Control''' port  1. connect CW Skimmer's '''CAT interface''' to PowerSDR-IF's '''CAT Control''' port

  a. establish a [:ConnectedVirtualSerialPortPairs: connected pair of virtual serial ports] using [:SetupConfigureVSPManager: VSP Manager] or [:SetupConfigurecom0com: com0com]; these instructions assume that connected virtual ports ''m'' and ''m+1'' are created (e.g. ''15'' and ''16'')

  a. select CW Skimmer's '''Command''' menu and ensure that there is no ''check mark'' to the left of the '''Blind Mode''' entry

  a. select CW Skimmer's '''View''' menu's '''Settings''' item to display the '''Settings''' window

  a. on CW Skimmer's '''Settings''' window's '''CAT''' tab,

     i. select '''Use Radio 1'''

     i. click the '''Configure...''' button

     i. on the '''Omni-Rig Settings''' window's '''RIG 1''' tab

        * set the '''Rig type''' selector to ''TS-2000''

        * set the '''Port''' selector to ''m+1''

        * set the '''Baud rate''' selector to ''57600''

        * set the '''Data bits''' selector to ''8''

        * set the '''Parity''' selector to ''None''

        * set the '''Stop bits''' selector to ''1''

        * set the '''RTS''' and '''DTR''' selector to ''Low''

        * set the '''Poll int., ms''' and '''Timeout, ms''' selectors to ''100''

        * click the '''OK''' button to the '''Omni-Rig Settings''' window

     i. click the '''OK''' button to close the '''Settings''' window
Line 11: Line 45:
 1. Configure CW Skimmer's '''CAT interface''' for a '''Rig type''' of ''TS-2000'' and a '''Vaud rate''' of ''57600''
1. in the '''Secondary CAT Serial Port''' panel on the '''Config''' window's '''Ports''' tab,

  a. set the '''CAT protocol''' selector to ''Elecraft''

  a. select '''Follow & Lead Primary'''

  a. set the '''Port#''' to ''N'', the '''Baud''' selector to ''9600'', the '''Word''' selector to ''8'', the '''Parity''' selector to ''None'', and the '''Stop''' selector to ''1''

  a. check the '''Enable''' box

 1. Configure CW Skimmer's '''CAT interface''' for a '''Rig type''' of ''TS-2000'' and a '''Baud rate''' of ''57600''

 1. Open PowerSDR-IF's '''Setup''' window; on the '''CAT Control''' tab

    a. enable '''CAT'''

    a.

Enabling Commander to interoperate with the PowerSDR-IF Panadapter and CW Skimmer

de Joe W4TV

This configuration provides simultaneous IF panadapter and [http://www.dxatlas.com/CwSkimmer CW Skimmer] functionality using WU2X's [http://www.wu2x.com/sdr.html PowerSDR-IF Stage panadapter].

  1. connect CW Skimmer's CAT interface to PowerSDR-IF's CAT Control port

    1. establish a [:ConnectedVirtualSerialPortPairs: connected pair of virtual serial ports] using [:SetupConfigureVSPManager: VSP Manager] or [:SetupConfigurecom0com: com0com]; these instructions assume that connected virtual ports m and m+1 are created (e.g. 15 and 16)

    2. select CW Skimmer's Command menu and ensure that there is no check mark to the left of the Blind Mode entry

    3. select CW Skimmer's View menu's Settings item to display the Settings window

    4. on CW Skimmer's Settings window's CAT tab,

      1. select Use Radio 1

      2. click the Configure... button

      3. on the Omni-Rig Settings window's RIG 1 tab

        • set the Rig type selector to TS-2000

        • set the Port selector to m+1

        • set the Baud rate selector to 57600

        • set the Data bits selector to 8

        • set the Parity selector to None

        • set the Stop bits selector to 1

        • set the RTS and DTR selector to Low

        • set the Poll int., ms and Timeout, ms selectors to 100

        • click the OK button to the Omni-Rig Settings window

      4. click the OK button to close the Settings window

  2. Using a second [:ConnectedVirtualSerialPortPairs: Connected Virtual Serial Port Pair], connect PowerSDR-IF's IF Setup port to Commander's Secondary CAT Serial Port.

1. in the Secondary CAT Serial Port panel on the Config window's Ports tab,

  1. set the CAT protocol selector to Elecraft

  2. select Follow & Lead Primary

  3. set the Port# to N, the Baud selector to 9600, the Word selector to 8, the Parity selector to None, and the Stop selector to 1

  4. check the Enable box

  1. Configure CW Skimmer's CAT interface for a Rig type of TS-2000 and a Baud rate of 57600

  2. Open PowerSDR-IF's Setup window; on the CAT Control tab

    1. enable CAT

Configured in this way, CW Skimmer controls PowerSDR-IF, and PowerSDR-IF controls your Primary Transceiver via Commander.

[http://www.dxlabsuite.com/Wiki/Graphics/Commander/K3SkimmerPanadapter.jpg]

Additional Topics

  • [:TransceiverControl:Getting Started with Transceiver Control]

  • [:TransceiverConnection:Connecting a Transceiver to a PC]

  • [:FrequencyControl:Changing Frequency]

  • [:ModeControl:Changing Mode]

  • [:Memories:Using Memories]

  • [:FrequencyDependentDevices:Using Frequency-dependent devices]

  • [http://www.dxlabsuite.com/commander/Help/CommandSequences.htm Using User-defined Command Sequences]


[http://groups.yahoo.com/group/dxlab/post Post a question or suggestion on the DXLab reflector]

[:GettingStarted:Getting Started with DXLab]

PowerSDRIFSkimmerCommander (last edited 2018-07-05 20:12:16 by AA6YQ)