Size: 3700
Comment:
|
Size: 3631
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 5: | Line 5: |
This configuration provides simultaneous IF panadapter and [http://www.dxatlas.com/CwSkimmer CW Skimmer] functionality using WU2X's [http://www.wu2x.com/sdr.html PowerSDR-IF Stage panadapter]. | This configuration provides simultaneous IF panadapter and [http://www.dxatlas.com/CwSkimmer CW Skimmer] functionality using WU2X's [http://www.wu2x.com/sdr.html PowerSDR-IF Stage panadapter]. Configured in this way, CW Skimmer controls PowerSDR-IF, and PowerSDR-IF controls your Primary Transceiver via Commander. [http://www.dxlabsuite.com/Wiki/Graphics/Commander/K3SkimmerPanadapter.jpg] |
Line 53: | Line 55: |
i. set the '''Baud''' selector to ''57600'' i. set the '''Parity''' selector to ''none'' i. set the '''Stop''' selector to ''1'' |
i. set the '''Baud''' selector to ''57600'', the '''Parity''' selector to ''none'', the '''Stop''' selector to ''1'' |
Line 62: | Line 60: |
Configured in this way, CW Skimmer controls PowerSDR-IF, and PowerSDR-IF controls your Primary Transceiver via Commander. [http://www.dxlabsuite.com/Wiki/Graphics/Commander/K3SkimmerPanadapter.jpg] |
Enabling Commander to interoperate with the PowerSDR-IF Panadapter and CW Skimmer
de Joe W4TV
This configuration provides simultaneous IF panadapter and [http://www.dxatlas.com/CwSkimmer CW Skimmer] functionality using WU2X's [http://www.wu2x.com/sdr.html PowerSDR-IF Stage panadapter]. Configured in this way, CW Skimmer controls PowerSDR-IF, and PowerSDR-IF controls your Primary Transceiver via Commander.
[http://www.dxlabsuite.com/Wiki/Graphics/Commander/K3SkimmerPanadapter.jpg]
Connect PowerSDR-IF's IF Setup port to Commander's Secondary CAT Serial Port
establish a [:ConnectedVirtualSerialPortPairs: connected pair of virtual serial ports] using [:SetupConfigureVSPManager: VSP Manager] or [:SetupConfigurecom0com: com0com]; these instructions assume that connected virtual ports n and n+1 are created (e.g. 13 and 14)
in the Secondary CAT Serial Port panel on Commander's Configuration window's Ports tab,
set the CAT protocol selector to Kenwood
select Follow & Lead Primary
set the Port# to n, the Baud selector to 57600, the Word selector to 8, the Parity selector to None, and the Stop selector to 1
check the Enable box
connect CW Skimmer's CAT interface to PowerSDR-IF's CAT Control port
establish a [:ConnectedVirtualSerialPortPairs: connected pair of virtual serial ports] using [:SetupConfigureVSPManager: VSP Manager] or [:SetupConfigurecom0com: com0com]; these instructions assume that connected virtual ports m and m+1 are created (e.g. 15 and 16)
select CW Skimmer's Command menu and ensure that there is no check mark to the left of the Blind Mode entry
select CW Skimmer's View menu's Settings item to display the Settings window
on CW Skimmer's Settings window's CAT tab,
select Use Radio 1
click the Configure... button
on the Omni-Rig Settings window's RIG 1 tab
set the Rig type selector to TS-2000
set the Port selector to m+1, the Baud rate selector to 57600, the Data bits selector to 8, the Parity selector to None, the Stop bits selector to 1, and the RTS and DTR selector to Low
set the Poll int., ms and Timeout, ms selectors to 100
click the OK button to the Omni-Rig Settings window
click the OK button to close the Settings window
Open PowerSDR-IF's Setup window and select its CAT Control tab
check the Enable CAT box
set the Baud selector to 57600, the Parity selector to none, the Stop selector to 1
set the ID as selector to TS-2000
Additional Topics
[:TransceiverControl:Getting Started with Transceiver Control]
[:TransceiverConnection:Connecting a Transceiver to a PC]
[:FrequencyControl:Changing Frequency]
[:ModeControl:Changing Mode]
[:Memories:Using Memories]
[:FrequencyDependentDevices:Using Frequency-dependent devices]
[http://www.dxlabsuite.com/commander/Help/CommandSequences.htm Using User-defined Command Sequences]
[http://groups.yahoo.com/group/dxlab/post Post a question or suggestion on the DXLab reflector]
[:GettingStarted:Getting Started with DXLab]