== Operating in PSK == === Setting up for PSK Operation === 1. [[AudioConnections| establish Transceiver-to-Soundcard Audio connections and select Soundcard]] 1. [[PTTMechanism| establish and configure the Transceiver-to-PC PTT (reception-transmission switching) connection]] 1. [[ConfigurePSK| Configure WinWarbler]] 1. Configure your transceiver a. if [[TransceiverControl| Commander]] isn't running, set your transceiver's mode to ''USB'' a. set your transceiver frequency to an open PSK band ||160m||1,807, 1,838 kHz|| ||80m||3,580 kHz|| ||40m||7,035, 7,070 kHz|| ||30m||10,138 kHz|| ||20m||14,070 kHz|| ||17m||18,100 kHz|| ||15m||21,070 kHz|| ||12m||24,920 kHz|| ||10m||28,120 kHz|| a. disable compression a. disable all receiver filtering (re-visit this later when operating on a crowded band) 1. [[SettingAudioInputLevel|Set the Audio Input Level]] 1. [[SettingAudioOutputLevel|Set the Audio Output Level]] <
> === Annotated Main window in PSK Mode === {{http://www.dxlabsuite.com/Wiki/Graphics/WinWarbler/PSK.jpg}} === Operating in PSK: Decoding PSK Signals === With its '''Operating Mode''' panel set to ''PSK31'' or ''PSK63'' or ''PSK125'', !WinWarbler's Main window provides a Waterfall or Spectrum display, and 3 '''Receive Panes''', each capable of independently decoding and displaying a PSK signal. The choice of ''Waterfall'' or ''Spectrum'' is governed by the '''Tuning Display''' panel on the '''Configuration''' window's '''PSK''' tab; these instructions assume that you've chosen a Waterfall display. The vertical height and horizontal zoom of the Waterfall or Spectrum display is controlled by the '''Tuning Display''' panel on the Main window, as shown in the screen shot above. The three Receive Panes are labeled 0, 1, and 2. The left side of each pane displays a colored panel, initially yellow for pane 0, green for pane 1, and light blue for pane 2, as shown in the screenshot above. Each receive panel will continuously decode whatever PSK it encounters on its assigned frequency. To control a Receive Pane, click anywhere within that Receive Pane to make it the '''Active Receive Pane'''. When you do this, two things will happen: 1. the number shown in the colored panel along the pane's left side will be shown in red font. 1. The '''Receive Channel''' panel above the '''Waterfall display''' will display the Active Receive Pane's current frequency, signal quality, squelch setting, and phase display. The frequency that a Receive Pane is decoding is highlighted in the '''Waterfall display''' in one of two ways, determined by the '''channel ID''' sub-panel in the '''Receiver''' panel on the Configuration window's '''PSK''' tab. In the screenshot above, the '''channel ID''' sub-panel is set to ''traces'', so the Waterfall shows a colored vertical trace designating each Receive Pane's receive frequency: the yellow trace shows the frequency being decoded by Receive Pane 0, the green trace shows the frequency being decoded by Receive Pane 1, and the light blue trace shows the frequency being decoded by Receive Pane 2. If you were to change the '''channel ID''' sub-panel from ''traces'' to ''markers'', then each receive pane's frequency would be denoted by colored triangles just above the Waterfall Display. When you click in the Waterfall Display with the left mouse button, you are setting the receive frequency for the Active Receive Pane -- the one whose number along the left edge is rendered in red font, and whose frequency is being displayed in the '''Receive Channel''' panel. Thus you can quickly tell which frequencies are being decoded by each Receive Pane -- they are highlighted by the yellow-, green-, and light blue-colored traces in (or triangles above) the Waterfall Display. To use a particular Receive Pane to decode a particular PSK signal, first click in that Receive Pane to make it the Active Receive Pane, and then click on the desired signal in the Waterfall Display. A colored trace will appear in the Waterfall (or a colored marker will appear above the Waterfall) at the point that you clicked, and the selected frequency will be displayed in the '''Receive Channel''' panel above the Waterfall Display. The horizontal bar in the '''Receive Channel''' panel displays signal quality and provides a squelch setting for the Active Receive panel. Signal quality is graphically indicated by the length of a red or yellow horizontal bar; a numeric value ranging from 0 (lowest quality) to 100 (highest quality) is displayed just to the left of the bar. Signal quality is a measure of phase noise, not signal strength; the higher the indicated quality, the more likely the text decoded from the signal is likely to be correct. The squelch mechanism lets you suppress the decoding of text when the signal's quality falls below a minimum that you establish via the setting of the dark blue vertical bar in the signal quality display. When the signal quality falls below the value set by this bar, the signal quality rectangle is shown in red, and the Active Receive Pane will not display new characters decoded from the signal; when the signal quality exceeds the value set by the squelch bar's position, the signal quality rectangle is shown in yellow, and the Receive Pane displays newly decoded characters. You can move the squelch bar's position by using the mouse to drag it to the left (decreasing the threshold) or to the right (increasing the threshold). You can control how rapidly the squelch is applied via the '''squelch speed''' sub-panel in the '''Receive''' panel on the Configuration window's '''PSK''' tab; the ''fast'' setting is recommended. All three Receive Panes have independent squelch settings, but you only see (and control) the squelch setting for the Active Receive Pane. To adjust the squelch of a Receive Pane that isn't currently active, click in that Receive Pane to activate it, and then adjust its squelch setting. '''Search''' and '''AFC''' ('''Automatic Frequency Control''') help with two issues arising from the relatively narrow width of PSK signals: 1. its hard to precisely tune a PSK signal using your transceiver's tuning knob 2. if either your QSO partner's transmitter or your receiver drifts during the QSO, you may fail to decode transmitted characters !WinWarbler's Search mechanism will ''lock on'' to the center of a PSK signal that is ''near'' the frequency you have designated by clicking in the '''Waterfall Display'''. The definition of ''near'' is controlled by the '''search range''' slider in the '''tuning''' sub-panel on the Configuration window's '''PSK''' tab. Setting this slider to 0 means that !WinWarbler will not adjust the Receive Pane frequency you select by clicking in the Waterfall Display, whereas setting this slider to 50 means that !WinWarbler will locate the nearest PSK signal within 50 hz of the frequency you clicked, and set the Active Receive Pane's frequency to that signal's frequency. By enabling '''Search''' with the '''search range''' set to 50, the need to manually tune a new PSK signal by adjusting your transceiver frequency while monitoring the '''Receive Channel''' panel's circular phase display is eliminated. Once a '''Receive Pane''' is decoding a PSK signal, !WinWarbler's '''AFC''' function, if enabled, will automatically change the Receive Pane's frequency to track changes in that signal's frequency. The limit of this tracking is set by the '''AFC limit''' slider in the tuning panel on the Configuration window's '''PSK''' tab; 100 hz is a reasonable value for '''AFC limit'''. '''AFC''' is enabled or disabled via a checkbox in the '''Receive Channel''' panel on the Main window. The '''Net''' function, when enabled, causes your transmit frequency to automatically track your receive frequency. This is convenient when calling a station on a particular frequency, but '''Net''' should be disabled as soon as a QSO begins so that any changes to your received frequency made by the '''AFC''' function in response to drift in your QSO partner's signal aren't reflected in your own transmit signal's frequency. <
> === Operating in PSK: Responding to a Station that is Calling CQ === 1. on the '''Configuration''' window's '''PSK''' tab, set the '''Tuning Display''' panel to ''Waterfall'' 1. click the '''PSK31''' button in the '''Main''' window's '''Operating Mode''' panel. 1. activate '''Receive Pane 0''' by clicking anywhere within it; the color of the number 0 shown in the yellow panel on its left border will change from black to red to indicate that '''Receive Pane 0''' is active 1. check the '''Receive''' panel's '''AFC''' box 1. check the '''Transmit''' panel's '''Net''' box; this will cause your transmit frequency to follow your receive frequency 1. click on a signal in the waterfall display; the yellow trace that indicates '''Receive Pane 0's''' frequency will appear at the selected frequency, and decoded characters will appear in '''Receive Pane 0''' a. adjust the blue vertical bar representing the '''Squelch''' setting in the the horizontal '''Signal Quality Display''' for optimal decoding a. to decode characters from another signal in the waterfall, click on that signal 1. when you find a signal to which you want to respond, uncheck the '''Transmit''' panel's '''Net''' box; this will keep your transmit signal from subsequently moving during the QSO 1. to transmit, a. click the '''Start''' button in the '''Transmit''' panel a. type the characters to be sent in the '''Transmit Pane''' (e.g. ''P5DX P5DX de AA6YQ AA6YQ kn'') a. click the '''Stop''' button in the '''Transmit''' panel; your transceiver should switch from reception to transmission, transmitted characters should appear in '''Receive Pane 0''', and your transceiver should switch from transmission to reception after all characters have been sent. <
> === Operating in PSK: Calling CQ and Responding === 1. on the '''Configuration''' window's '''PSK''' tab, set the '''Tuning Display''' panel to ''Waterfall'' 1. click the '''PSK31''' button in the '''Main''' window's '''Operating Mode''' panel. 1. activate '''Receive Pane 0''' by clicking anywhere within it; the color of the number 0 shown in the yellow panel on its left border will change from black to red to indicate that '''Receive Pane 0''' is active 1. check the '''Receive''' panel's '''AFC''' box 1. check the '''Transmit''' panel's '''Net''' box; this will cause your transmit frequency to follow your receive frequency 1. look for a frequency in the waterfall that's remained unused for at least a minute, and click on it; the yellow trace that indicates '''Receive Pane 0''' frequency is monitoring this frequency 1. uncheck the '''Transmit''' panel's '''Net''' box; this will prevent your transmit frequency from subsequently moving 1. call CQ a. click the '''Start''' button in the '''Transmit''' panel a. type the characters to be sent in the '''Transmit Pane''' (e.g. ''CQ CQ CQ de AA6YQ AA6YQ AA6YQ k'') a. click the '''Stop''' button in the '''Transmit''' panel; your transceiver should switch from reception to transmission, transmitted characters should appear in '''Receive Pane 0''', and your transceiver should switch from transmission to reception after all characters have been sent. 1. '''Receive Pane 0''' will lock on to any signal close to your transmitting frequency, and display decoded characters; adjust the blue vertical bar representing the '''Squelch''' setting in the the horizontal '''Signal Quality Display''' for optimal decoding <
> === Additional Capabilities === * Instead of transmitting by manually clicking the '''Start''' button, typing text, and clicking the '''Stop''' button, you can [[Macros|define macros ]] that can be initiated with a single mouse click or '''Function Key''' strike, like these: {{{ de kn cq cq cq de k }}} * You can [[DisplayingDecodedInformation|manage the display of decoded information]] * You can [[CapturingDecodedInformation|capture decoded information]] for [[http://www.dxlabsuite.com/winwarbler/Help/Logging.htm|Logging QSOs]]. * You can use !WinWarbler's [[http://www.dxlabsuite.com/winwarbler/Help/BroadbandDecode.htm|Broadband Decoder]] to simultaneously decode all active PSK signals on the band, and quickly respond to one of them. * The '''Omega 25''' button in the Main window's '''Receive Channel''' panel replays the last 25 seconds of audio, enabling all three Receive Panes to decode and display text from the replayed audio. This can be helpful when you click on a PSK signal in the Waterfall and see that the op is introducing himself or herself, meaning that you just missed seeing the station's callsign. Click the '''Omega 25''' button, and you'll likely see the callsign as !WinWarbler decodes the audio received before you selected this station's frequency to decode. * Transmitting with audio tones less than 1500 Hz. can produce harmonics, while transmitting with audio tones above 2400 Hz. can reduce transmitted power due to transceiver passband filtering; to prevent this, a. set the '''Optimal Offset''' to ''1500'' on the Configuration window's '''PSK''' tab a. [[TransceiverControl| configure and run Commander]] to enable !WinWarbler to control your transceiver a. after selecting a frequency in the Waterfall by clicking it, click the '''Opt''' button in !WinWarbler's '''Receive''' panel; this will direct Commander to QSY your transceiver so that the designated signal lies at exactly 1500 Hz. <
> === Introductory Information === * [[http://www.podxs070.com/frequently-asked-questions/introduction-to-psk|Introduction to PSK31]] ---- [[DXLabDiscussionGroup|Post a question or suggestion on the DXLab Discussion Group]] [[Operation|Operating in CW, Phone, PSK, and RTTY]] [[GettingStarted|Getting Started with DXLab]]